Sticker Workbench

Workbench guide

Check a backing card's hole and safe artwork region

Check a backing card's hole and safe artwork region

Try a 60 × 90 millimeter card, a round 4 millimeter hanger hole, horizontal center 30 millimeters and a 5 millimeter top-edge clearance. The hole center is 7 millimeters down and the region through 9 millimeters from the top contains the hole. Reserve artwork space deliberately, then check how the attached item sits on the card. The tool checks a geometric boundary, not material strength or how a real hanger behaves. Inspect the exported trim, bleed and safety layers before printing and punching a sample.

How to use

Enter the card, hanger and sheet dimensions. Check the hanger position and the paper around it. No load capacity or fastening strength is guaranteed.

Measure a hole from the correct reference edge

Distinguish the distance to the center of a hole from the distance to its nearest edge. For a round hole, adding the radius to an edge clearance gives its center position. Check that the entire hole fits inside the tag or card and that important content stays clear of it. Geometric fit does not establish tear strength or suitability for a particular hanger. Test the actual material, attachment and handling direction before using the same layout for a larger batch.

Write down the measurement before opening the calculator

Measure the actual item, not the outside of its packaging or a screen preview. Record the unit beside each number. This site converts one inch to exactly 25.4 millimeters; changing a unit selector does not make an uncertain measurement more precise. Measure both axes and check whether a folded, rounded or thick object needs additional clearance. Keep the original measurement separate from any allowance you add later, so another person can reproduce the calculation without guessing which dimensions already contain extra space.

Separate the finished item from the printable canvas

The trim size describes the finished object after cutting. A sheet or image canvas may be larger because it also contains margins, bleed or marks. Start with the finished width and height, then add the other spaces explicitly. Do not enter a dimension that already includes bleed and ask the calculator to add the same bleed again. Label your notes with the intended finished size, and compare that size with the exported file rather than assuming the preview border is the cut edge.

Add bleed only where the artwork needs it

Bleed extends a background beyond the intended cut. It is not extra room for text, and it does not correct an inaccurate printer scale. Obtain the required amount from the print provider or your tested cutting workflow. For a rectangular item, the new width is the trim width plus twice the bleed, and the new height is the trim height plus twice the bleed. This does not double the original width or height. Check neighboring items as well: two artworks extending into the same gap may overlap even when their trim outlines do not touch.

Keep important content inside a safe zone

A safe zone moves important content inward from the trim edge. Place small text, a logo, a code and other critical details inside it before filling the background out to bleed. A chosen safe distance is an allowance, not a guarantee about a particular cutter. Avoid putting a thin decorative border exactly on the trim, where a small cutting shift becomes obvious. Examine narrow corners and the space beside a hole or fold separately; a rectangular inset alone does not describe every risk.

Read the grid calculation rather than trusting empty space

A regular sheet grid counts complete columns and rows after subtracting outside margins and allowing gaps between items. Counts round down because a fraction of an item is not printable stock. A little unused space along an edge may be unavoidable in that grid. Area utilization is useful for comparing arrangements, but it does not prove that a layout is practical to feed, cut or sort. Check the placement diagram and the count together, especially when an item nearly touches the usable boundary.

Inspect SVG dimensions and layers before using a cutter

An SVG can describe geometry at a physical size through its outer dimensions and coordinate system. Confirm the width, height and viewBox on import instead of assuming a drawing application preserves them unchanged. Trim outlines, bleed and safe-zone guides serve different purposes; do not send every visible guide to a cutter as a cut path. This site's simple outlines are planning geometry, not a device-specific cutting job. Check layers, stroke handling and an actual-size sample in the software that will control your equipment.

Make a small physical proof before repeating the output

Print one sample with the same paper, application and settings you plan to use for the run. Disable an unintended fit-to-page option when checking a file intended for actual-size output. Measure a known dimension, inspect important edges and test the relevant action: cut, fold, scan, insert or attach. A correct mathematical layout can still fail because of feeding, registration, material thickness or printer scaling. Record the observed difference before changing the model, so a correction addresses a measured problem instead of a guess.

Open tool: Backing Card Imposition

Questions & answers

Does the hole position prove that a product is secure?

No. Test the board, hole, fastener and actual product together.

How is the top distance measured?

It runs from the top card edge to the top of the hole or slot, not to its center.

Will the hanger rotate with the card?

Yes. The outline and hanger rotate together in the uniform sheet layout.

Last reviewed ·

Reference and verification