Sticker Workbench

Workbench guide

Place a tag hole using edge clearance rather than its center

Place a tag hole using edge clearance rather than its center

Use a 50 × 80 millimeter tag, a 4 millimeter round hole and a 5 millimeter clearance from the top edge to the hole's nearest edge. The center is 25 millimeters from the left and 7 millimeters from the top; the hole extends to 9 millimeters from the top. Keep artwork away from that region and inspect the full hole boundary. These values check geometry only. They do not predict tear resistance, attachment strength or suitability for a particular punch and material.

How to use

The hole is centered horizontally. Its edge is separated from the top by the entered distance. Test your own punch or cutter; equipment precision is not guaranteed.

Write down the measurement before opening the calculator

Measure the actual item, not the outside of its packaging or a screen preview. Record the unit beside each number. This site converts one inch to exactly 25.4 millimeters; changing a unit selector does not make an uncertain measurement more precise. Measure both axes and check whether a folded, rounded or thick object needs additional clearance. Keep the original measurement separate from any allowance you add later, so another person can reproduce the calculation without guessing which dimensions already contain extra space.

Measure a hole from the correct reference edge

Distinguish the distance to the center of a hole from the distance to its nearest edge. For a round hole, adding the radius to an edge clearance gives its center position. Check that the entire hole fits inside the tag or card and that important content stays clear of it. Geometric fit does not establish tear strength or suitability for a particular hanger. Test the actual material, attachment and handling direction before using the same layout for a larger batch.

Keep important content inside a safe zone

A safe zone moves important content inward from the trim edge. Place small text, a logo, a code and other critical details inside it before filling the background out to bleed. A chosen safe distance is an allowance, not a guarantee about a particular cutter. Avoid putting a thin decorative border exactly on the trim, where a small cutting shift becomes obvious. Examine narrow corners and the space beside a hole or fold separately; a rectangular inset alone does not describe every risk.

Separate the finished item from the printable canvas

The trim size describes the finished object after cutting. A sheet or image canvas may be larger because it also contains margins, bleed or marks. Start with the finished width and height, then add the other spaces explicitly. Do not enter a dimension that already includes bleed and ask the calculator to add the same bleed again. Label your notes with the intended finished size, and compare that size with the exported file rather than assuming the preview border is the cut edge.

Read the grid calculation rather than trusting empty space

A regular sheet grid counts complete columns and rows after subtracting outside margins and allowing gaps between items. Counts round down because a fraction of an item is not printable stock. A little unused space along an edge may be unavoidable in that grid. Area utilization is useful for comparing arrangements, but it does not prove that a layout is practical to feed, cut or sort. Check the placement diagram and the count together, especially when an item nearly touches the usable boundary.

Leave device-specific cutting decisions to the tested workflow

A geometric outline does not contain every setting a cutting device needs. Tool choice, offset, blade behavior, registration marks and the material can affect the result. Do not infer those settings from a plain SVG or a rectangular preview. Keep a clear distinction between artwork, trim guides and the production cut path. Test a small piece first and inspect corners, tight curves and release from the backing. A higher calculated yield per sheet is not useful if the chosen spacing makes the pieces difficult to cut reliably.

Check the assembled item as well as its flat dimensions

A flat drawing cannot fully describe a finished card, wrapped label or attached tag. Make a sample with the intended stock and inspect the assembled result. Check where a seam, overlap, score or hole sits relative to important artwork. A material can bend, compress or resist a fold in ways that simple geometry does not predict. Keep the measured flat values and your observed adjustment as separate notes, and rerun the calculator if the tested specification changes rather than editing the final file by eye.

Make a small physical proof before repeating the output

Print one sample with the same paper, application and settings you plan to use for the run. Disable an unintended fit-to-page option when checking a file intended for actual-size output. Measure a known dimension, inspect important edges and test the relevant action: cut, fold, scan, insert or attach. A correct mathematical layout can still fail because of feeding, registration, material thickness or printer scaling. Record the observed difference before changing the model, so a correction addresses a measured problem instead of a guess.

Open tool: Hang Tag & Hole Spacing

Questions & answers

Is this a production guarantee?

No. Verify printer margins and your material before a full batch.

Does this use a server?

No. All calculations and files are generated in this browser.

How should I print?

Select actual size / 100%, then check the reference dimensions with a ruler.

Last reviewed ·

Reference and verification