Sticker Workbench

Workbench guide

Inspect the pieces placed by a mixed-size shelf plan

Inspect the pieces placed by a mixed-size shelf plan

Try a 100 × 100 millimeter sheet, 5 millimeter margins and a 5 millimeter gap with two 40 × 40 pieces and two 30 × 30 pieces. These four pieces fit in the tested shelf arrangement. The tool compares entered order with a height-sorted order; it does not rotate every piece or prove an optimal nest. Check the placed count of each requested size, not just the total. If an important size is omitted, compare a separate-sheet plan instead of assuming a small unused region can accept it.

How to use

Compare two shelf orders of 2–4 rectangular sizes; no optimality guarantee. All lengths use the selected unit. Preview and test a physical sheet before production.

Read the limitations of a mixed-size arrangement

The mixed-size tool compares two shelf orders rather than searching every possible arrangement. Inspect which pieces were actually placed and which were omitted when space ran out. A total count alone can hide an inconvenient mixture if one size matters more to the order. Keep quantity requirements visible and compare a separate-sheet plan when sorting or cutting becomes difficult. Small unused regions do not prove that another requested piece can fit there; its width, height, orientation and required spacing must all be considered together.

Read the grid calculation rather than trusting empty space

A regular sheet grid counts complete columns and rows after subtracting outside margins and allowing gaps between items. Counts round down because a fraction of an item is not printable stock. A little unused space along an edge may be unavoidable in that grid. Area utilization is useful for comparing arrangements, but it does not prove that a layout is practical to feed, cut or sort. Check the placement diagram and the count together, especially when an item nearly touches the usable boundary.

Compare orientations without assuming an optimal nest

Rotating a rectangular item can change both the column count and the row count. Compare the two complete grid orientations when the tool supports them, and check which orientation the reported winner actually uses. The winner is the best of the tested layouts, not a proof that no mixed arrangement could fit more. Grain direction, artwork direction, a flap, a fold or a required reading order may also rule out the numerical winner. Keep a lower-yield arrangement when it better matches the physical job.

Budget spacing between neighboring pieces

An outside sheet margin and an inside gap solve different problems. The margin reserves space beside the sheet edge; the gap separates neighboring pieces. A gap must leave room for any bleed, cutting allowance or handling space your process needs. Do not subtract those allowances from a reported gap a second time without checking the model. Draw two neighboring trim edges and their extra zones on paper if the terminology is unclear, then enter the resulting distance deliberately rather than using a familiar-looking default.

Separate the finished item from the printable canvas

The trim size describes the finished object after cutting. A sheet or image canvas may be larger because it also contains margins, bleed or marks. Start with the finished width and height, then add the other spaces explicitly. Do not enter a dimension that already includes bleed and ask the calculator to add the same bleed again. Label your notes with the intended finished size, and compare that size with the exported file rather than assuming the preview border is the cut edge.

Separate requested quantity from planned production

Write down the number of usable pieces you need, the yield of one sheet or repeat, and any allowance separately. A target is not automatically the quantity that fits into complete sheets. The planned run may produce extra pieces, and a percentage estimate does not guarantee an exact number of good results. Keep those extra pieces visible in the notes so they do not become an accidental cost omission. Recalculate the plan when the yield changes instead of carrying an old sheet count into a new layout.

Leave device-specific cutting decisions to the tested workflow

A geometric outline does not contain every setting a cutting device needs. Tool choice, offset, blade behavior, registration marks and the material can affect the result. Do not infer those settings from a plain SVG or a rectangular preview. Keep a clear distinction between artwork, trim guides and the production cut path. Test a small piece first and inspect corners, tight curves and release from the backing. A higher calculated yield per sheet is not useful if the chosen spacing makes the pieces difficult to cut reliably.

Make a small physical proof before repeating the output

Print one sample with the same paper, application and settings you plan to use for the run. Disable an unintended fit-to-page option when checking a file intended for actual-size output. Measure a known dimension, inspect important edges and test the relevant action: cut, fold, scan, insert or attach. A correct mathematical layout can still fail because of feeding, registration, material thickness or printer scaling. Record the observed difference before changing the model, so a correction addresses a measured problem instead of a guess.

Open tool: Multi-Size Sheet Mix

Questions & answers

Is this a production guarantee?

No. Verify printer margins and your material before a full batch.

Does this use a server?

No. All calculations and files are generated in this browser.

How should I print?

Select actual size / 100%, then check the reference dimensions with a ruler.

Last reviewed ·

Reference and verification